Major Section: EVENTS
When one submits an
progn event and one of its
sub-events fails, ACL2 restores its logical world as though the
progn had not been run. But sometimes one would like
to debug the failure by re-executing all sub-events that succeeded up to the
point of failure, and then re-executing the failed sub-event. Said
differently, imagine that the top-level
progn form, as
well as all such sub-forms, were flattened into a list of events that were
then submitted to ACL2 up to the point of failure. This would put us in the
state in which the original failed event had failed, so we could now submit
that failed event and try modifying it, or first proving additional events,
in order to get it admitted.
Redo-flat is provided for this purpose. Consider the following (rather
nonsensical) example, in which the
f3 fails (the body is
y but the formal parameter list is
(encapsulate () (defun f1 (x) x) (encapsulate () (local (defthm hack (equal (car (cons x y)) x)))) (encapsulate () (local (defthm hack (equal (+ x y) (+ y x))))) (encapsulate () (make-event '(defun f2 (x) x)) (progn (defthm foo (equal x x) :rule-classes nil) (defun f3 (x) y))) (defun f4 (x) x) (defun f5 (x) y))After this attempt fails, you can evaluate the following form.
(redo-flat)This will first lay down a
(deflabel r), so that you can eventually remove your debugging work with
(:ubt! r). Then the successful sub-events that preceded the failure will be executed with proofs skipped (so that this execution is fast). Then, the failed event will be executed. Finally, a
pbtcommand is executed so that you can see a summary of the events that executed successfully.
You can eliminate some of the steps above by supplying keyword values, as follows.
(redo-flat :succ succ ; Skip the successful sub-events if val is nil. :fail fail ; Skip the failed sub-event if val is nil. :label lab ; Skip deflabel if lab or succ is nil, else use (deflabel lab). :pbt val ; Skip the final :pbt if val, lab, or succ is nil. )Also, you can avoid skipping proofs for the successful sub-events by supplying keyword
:succ-ld-skip-proofspwith a valid value for
ld-skip-proofsp; see ld-skip-proofsp.
If you prefer only to see the successful and failed sub-events, without any events being re-executed, you may evaluate the following form instead.
(redo-flat :show t)For the example above, this command produces the following output.
List of events (from encapsulate or progn) preceding the failure:
((DEFUN F1 (X) X) (ENCAPSULATE NIL (LOCAL (DEFTHM HACK (EQUAL (CAR (CONS X Y)) X)))) (ENCAPSULATE NIL (LOCAL (DEFTHM HACK (EQUAL (+ X Y) (+ Y X))))) (MAKE-EVENT '(DEFUN F2 (X) X)) (DEFTHM FOO (EQUAL X X) :RULE-CLASSES NIL))
(DEFUN F3 (X) Y) ACL2 !>
Redo-flat uses a scheme that should not cause spurious name conflicts for
local events. Above, it is mentioned that events are ``flattened'';
now we clarify this notion. Each sub-event that succeeds and is an
progn is left intact. Only such events that fail
are replaced by their component events. Thus, in the example above, there is
no conflict between the two
local sub-events named ``
because these are contained in successful
encapsulate sub-events, which
are therefore not flattened. The
progn and two
events surrounding the definition of
f3 are, however, flattened, because
that definition failed to be admitted.
Unfortunately, an event must actually fail in order for
work. So if the system is ``stuck'' on an event, then you may find it
helpful to insert an illegal event just in front of it before submitting the